SECURITY ACCESSORIES
Mounting Methods
- Rear mounting for walls up to 6" (150 mm) thick: "T" nuts and 1/4" – 20 threaded rods, nuts, washers and steel mounting channel provided.
- Rear mounting for walls 6" (150 mm) thick and over: "T" nuts and 1/4” – 20 threaded rods, nuts, washers and steel mounting channel provided.
- Front mounting: TORX head machine screws, 1/4" – 20 x 2" (50 mm) long, furnished. (Anchors to suit field conditions by others.)
Anchoring Information
- Front mounted units are furnished with TORX vandal resistant 1/4" – 20 x 2" (50 mm) machine screws. Wall anchors are not furnished with accessory.
- Rear mounted units are furnished with "T" nuts and 1/4" – 20 threaded rods with nuts and washers to suit 6" (150 mm) walls. Specify if walls are greater than 6" (150 mm).
- Wall Sleeves (optional). Recommended for mounting of accessories in poured, or precast concrete walls. Fabricated of Paintlok steel, all welded construction with mounting holes for attachment to forms.
RETRACTABLE SHOWER SEAT – FRONT MOUNTING
Seat folds up into cabinet. Fabricated of 12 gauge stainless steel, exposed surfaces have a satin finish. Seat has reinforced channels. Wall sub frame furnished, with welded on masonry anchors.
Sub Frame Opening:
15" x 15" x 2 3/4" (380 x 380 x 70 mm).
Sub Frame Opening:
15" x 15" x 2 3/4" (380 x 380 x 70 mm).
FRONT MOUNTING POST TYPE TOILET TISSUE HOLDER
Fabricated of 18 gauge 1 1/4" (32 mm) OD stainless steel type 304 with satin finish. Flange is 3" (76 mm) diameter x 1/8" (3 mm) thick and has 3 countersunk holes for front mounting.
SQUARE RECESSED TOILET TISSUE HOLDER – REAR MOUNTING
Fabricated of 14 gauge type 304 stainless steel with satin finish exterior, glass blasted satin finish interior 4 1/2" (115 mm) deep accommodates one standard toilet tissue roll. Flange is 7" (180 mm) square. Hidden contraband causes roll to project from holder allowing detection. Two "T" nuts welded on back for rear mounting.
SQUARE RECESSED TOILET TISSUE HOLDER - FRONT MOUNTING
Same as 110-1 except with front mounting holes.
RECESSED TOILET TISSUE HOLDER – REAR MOUNTING
Fabricated of 16 gauge type 304 stainless steel, satin finish exterior, glass blasted satin finish interior. 4 1/2" (115 mm) interior depth accommodates one standard toilet tissue roll. Hidden contraband causes roll to project from holder allowing detection. Two "T" nuts welded on back for rear mounting.
FOLDED TOILET TISSUE HOLDER - FRONT MOUNTING
Holder is 14 gauge type 304 stainless steel, satin finish. Open design for detection of contraband. Provided with 4 mounting holes for front mounting.
FRAMED MIRROR - REAR MOUNTING
Frame 14 gauge type 304 stainless steel with satin finish, corners welded and ground smooth. Unit provided with fiberboard backing and 6 "T" nuts welded on back for rear mounting. Specify glazing suffix required (see page 31 for legend) and also specify wall thickness if greater than 6" (150 mm).
see chart for standard sizes and surfaces.
see chart for standard sizes and surfaces.
FRAMED MIRROR – FRONT MOUNTING
Unit consists of wall mounting plate fabricated of 7 gauge type 304 stainless steel with 4 countersunk mounting holes and 8 tapped holes. Formed mirror fabricated of 18 gauge type 304 stainless steel with #8 mirror polish finish provided with 8 dimpled holes through integral frame and 1/4 - 20 x 1/4" TORX head screws for securing to wall mounting plate.
ONE PIECE FRAMED MIRROR WITH ROUNDED CORNERS – FRONT MOUNTING
One piece 18 gauge type 304 stainless steel formed mirror with #8 mirror polish finish, integral frame, rounded corners and 6 mounting holes.
ONE PIECE FRAMED MIRROR WITH ROUNDED CORNERS – REAR MOUNTING
Same as 107 with 6 "T" nuts welded on back for rear mounting
REAR MOUNTING RECESSED SOAP DISH
Soap dish 16 gauge stainless steel type 304 with satin finish. One piece drawn construction with beveled trim and embossments for air circulation and drainage. Unit has two "T" nuts welded on back for rear mounting.
FRAMED MIRROR – FRONT MOUNTING
Similar to 101, but front mounting, furnished with TORX vandal resistant 1/4 - 20 x 2" (150 mm) machine screws.
SECURITY GRAB BAR (REAR MOUNTED)
Tubing 18 gauge and flanges 1⁄8“ (3 mm) thick stainless steel type 304 with satin finish. Closure plate is 1⁄8" (3 mm) thick. All welded construction. Unit has 3 Threaded Rods in Welded Studs on each flange for rear mounting.
SECURITY GRAB BAR (REAR MOUNTED)
30" (760 mm)
SECURITY GRAB BAR (REAR MOUNTED)
36" (915 mm)
SECURITY GRAB BAR (REAR MOUNTED)
42" (1070 mm)
SECURITY GRAB BAR (REAR MOUNTED)
48" (1220 mm)
SECURITY GRAB BAR (FRONT MOUNTED)
Tubing 18 gauge and flanges 1⁄8“ (3 mm) thick stainless steel type 304 with satin finish. Closure plate is 1⁄8" (3 mm) thick. All welded construction. Unit has 3 holes through each flange for front mounting.
SECURITY GRAB BAR (FRONT MOUNTED)
30" (760 mm)
SECURITY GRAB BAR (FRONT MOUNTED)
36" (915 mm)
SECURITY GRAB BAR (FRONT MOUNTED)
42" (1070 mm)
SECURITY GRAB BAR (FRONT MOUNTED)
48" (1220 mm)
